Support network helps WiFi connection tracking
Due to the configuration of the system without problems and inexpensive systems for WiFi networking equipment has exploded dramatically in a few years. wireless network connection does not require drilling and keeps the labyrinth via wired. However, being a non-technical user home computer you might think twice before installing a WiFi network at home, taking into account the problems and difficulties. Now, troubleshooting network errors especially when it comes to a wirelessone, seems to be much more difficult that provide network support in a wired network configuration.
It is often difficult to obtain the network of our system after the installation of a WiFi network to the premise. If your computer has a network adapter and Windows operating system will automatically detect the wireless network within range of your computer. How to explain the technical support tutorials or the networksupport vendor guide, open the Start menu and go to the "Connect To" option. Here you will find the "Connect to a network" that will take you to the WiFi network connectivity. If your still not receiving any Windows network, you must follow certain steps to further inquiry.
Laptops or other wireless computer systems commonly have a wireless switch on the front of the computer. So, check your computer for theswitch and make sure it is turned on. This might sound stupid, but people usually just ignore these basic things, while solutions are found only there. Even the mind to control the computer if it uses a combination of function keys to operate the power switch. Expert software support to help users find the details about wireless switch location.
If the problem persists, check the wireless router. Make sure that the ID of the activated access point and wirelessSignal lights are illuminated. You can reset the router for 10-15 seconds and turning it back on again. However, this step will be to disconnect the network the entire system at the moment.
You can never ignore the possibility of interference from other devices. According to the microwave network of technical support and a sort of cordless can restrict your system to get the network connection by creating an obstacle. So it is always bettermaintain these high frequency gadget out of the reach of your network. If you can not turn the device certainly far from your WiFi network, you can change the access point or wireless router setup to a different channel.
If all your efforts have already gone in vain, try to re-configure the Windows installation again. Network support engineers are always ready to help in this regard. They provide simple steps to configure the operating system to connect tothe right kind of network. While direct, you must go to the Start menu, All Programs, then where are the accessories. Under accessories is an option called Command Prompt. You just change the type of network, your system will immediately begin receiving a wireless network connection.
In addition to the above rules, business support network provides many useful tips to work on other issues WiFi network seamlessly.
As more computers connect to a broadband Internet connection
Image : http://www.flickr.com
A broadband or high speed connection is what many people currently use in their home. Along with high-speed Internet, many users also use a router to connect multiple computers to the Internet. This document describes how a router is used to connect multiple computers here. To make it easier to understand, I'm going to use, in which we live Internet as a comparison of how the computer is connected to the Internet.
What is an IP address?
IP addresses are a seriesnumbers of the form: nnn, where nnn is a number of 1-3 digits. An IP address is unique to a single computer in a network, such as yours has a unique address. For an Internet connection, an IP address from your Internet service provider (ISP) delivered. In some cases, the ISP gives you more of an IP address that allows you to connect multiple computers here. As discussed below, but you can connect multiple computerswith a single IP address.
Connecting a single computer
Connecting a single computer to the Internet at high speed is your very easy to do. Simply connect a network cable to the modem and then the network card in your computer. The computer then your ISP assigned IP address. For example, if your ISP assigned IP address 24.24.50.17, then the computer has an IP address.
IfMake a request to a server, such as a Web page, the web server know the IP address the request is made. The information is then sent through the Internet and back to your computer. It 's like if someone sends mail to your home. The address on the mail can go home and not elsewhere.
Connect multiple computers
How can you connect multiple computers, whether assigned to a single address? If you have a request for a WebFirst, as it aims to know which computer requested page? We take our home analogy a step further. Let's say that instead of living in a house that you live in an apartment. If someone sends you mail, they belong to not only address but also an apartment. This number is internal to your house and every apartment has its own number. Similarly, multiple computers connected to the Internet when they were all there own local IP address. This canmanaged by a router.
A router is a piece of hardware that is directly to the modem. Each computer is then connected to the router, instead of the modem. Instead of using the IP address from your Internet service provider will now have computers, the router is now that the IP address assigned. This is similar to the router than the home.
The beauty of a router is that it has assigned its own local IP addresses. If you buy a computer with the routerassigned to receive an IP address of the router, similar to each his apartment number. Well, if you make a request for a Web page, the request must be sent to the same IP address, but this time is assigned to the router. If the Web page is returned, the router receives the request and sends it locally on the computer, the requested page.
The router also has its own local database, which is related to the IP addresses of the local computer. So now theRouter has two addresses are assigned to: an outsider from a local ISP and made available to him. This allows the network router to connect to the Internet and the local.
Note: The address is 192.168.xxx.xxx specific IP addresses) reserved for Local Area Networks (LANs.
Managing a Web or FTP server on the network
Let's take a look at this scenario. You have a router connecting multiple computers to the Internet. But now I want to To create an FTP or Web server. No problem. The installation of the necessary software on a computer network, said someone outside the local network IP address of the FTP server and try to connect. Then they discover that they can not connect. Why? His list something only someone like you to give your home number, no address.
The IP address assigned by your computer to your local network. You can connect to the socketComputers on the network but not from the Internet. You must use your ISP assigned IP address (assigned by the router) to have someone from the Internet to your FTP server to connect. The problem is that the router assigns IP and not the computer as an IP address must be unique, how can two computers have the same IP? The answer: they can not, but it is not.
Routers are able to retrieve information about a port forwarda specific computer. A port is a channel number, the data is sent across a network on. You can not see directly as a virtual channel is widely used in network for sending / receiving data. For the FTP server the default port is 21, but you can use another port.
Open the router configuration and find the option for port forwarding. Enter the internal IP address of FTP server and the port number and then save this information. Now, when a user tries toAccess to the FTP site, have the IP address assigned by your ISP to your router to use. The router will then be seen that the data sent to port 21 and then sends it automatically to the FTP server. A Web server can be set in the same way, but the default port is 80, in general,
Note: By default, a router to dynamically assign IP addresses to connected computers. This means that the first computer to connect to the IP router is to get the first availableAddress, and the next gets the second and so on. If you manage an FTP server, it may be easier to assign a static IP address to the computer to make sure the FTP server is always the same IP address.
This article describes how to connect one or more computers to an Internet connection. It 'important that the following points:
If you have a modem connected directly to your computer and your ISP assigned IP address of your computer.
Ifusing a router, the the router will be assigned the IP address from your ISP. Any computers connected to the router will be assigned a local address by the router.
A router will have the ISP IP address and a local IP address. This allows it to connect to both the Internet and your network.
When setting up a computer as a FTP, Web, or other server to communicate over the Internet, it is important to use the router’s IP address to access your server. You will then need to forward the necessary ports on the server.
For more information, read the blog technically simple.
How to connect multiple computers to a broadband Internet connection
Broadband or high-speed Internet connection is what many users are currently in use in their home. Along with high-speed Internet, many users can also use a router to connect multiple computers to the Internet. This document describes how to use a router to connect multiple computers. Easier to understand, I will use when you live as a comparison to how the computer is connected to the Internet.
What is an IP address?
IP addresses consist of a seriesnnn.nnn.nnn.nnn numbers in the form: nnn is the start of a three-digit number. An IP address is unique for a single computer in a network, just like at home, has a unique address. Provided a connection to the Internet, an IP address from your Internet service provider (ISP). In some cases, the ISP can have more than one IP address, which you can connect to multiple computers. As we shall see later, but it is still more computerswith a single IP address.
Connecting a single computer
Connecting a single computer to your high-speed Internet is very easy to do. Simply connect a network cable to the modem and then into the network card in your computer. Your computer will be assigned an IP address from your ISP. For example, if your ISP assigns you the IP address 24.24.50.17, then the IP address of the computer.
WhenSend a request to a server, such as a Web page, the web server knows what IP address that made the request. The information is then sent via the Internet and back to your computer. This is like when someone sends mail to your home. The address on the e-mail can be delivered at home and not elsewhere.
Multiple computers
How can connect multiple computers, if only one address is assigned? If you have a network request –First, as you know which computer on which the requested page? Let our home analogy a step further. Suppose, instead of living in a house that you live in an apartment. If someone sends you e-mail, not only address but also an apartment. This figure is inside your house apartment and each apartment has its own number. Similarly, multiple computers can connect to the Internet when they are there own local IP address. This canprocessed by a router.
A router is a piece of hardware that connects directly to the modem. Each computer is then connected to the router instead of the modem. Now, instead of the computer with the IP address from the provider, the router is now assigned the IP address provided. This is comparable to the router via the apartment.
The beauty of a router is that you can assign your own local IP addresses. If you use a computer to the router hoursreceives the IP address of the router, as each house has its own assigned number. If we now make a request to a Web page, the request is sent to the provider the same address, but this time is to assign to the router. If the Web page is returned, the router receives the request and sends it locally on your computer, the requested page.
The router also has its own local address, which is the local IP addresses of computers alone. Then there is theRouter has assigned two addresses: one provided by the external provider and one local, who has made available. This allows the router to connect to the Internet and local network.
Note: The address 192.168.xxx.xxx are special IP addresses for local area networks (LANs) are reserved.
Managing a Web or FTP server on the network
Let's take a look at this scenario. You have a router that connects multiple computers to the Internet. But now I want To create an FTP or Web server. No problem. The installer software is required on a computer network, "said someone outside the network, the local IP address of the FTP server and try to get in touch. Then he discovered that he can not connect. Why? Like something to someone list by simply pointing your home number and no address.
The IP address assigned to your computer on the network. You can connect to this> Computer networking, but not from the Internet. You need your ISP assigned IP address (assigned to the router) to have someone from the Internet to connect to FTP server. The problem is that the router assigns the IP address and the computer, and as an IP address must be unique, as two computers can share the same IP? The answer: you can not, but it is not.
Routers are able to provide information on a door to the fronta particular computer. A port is a channel numbered according to which data can be sent to a network. You can not physically see, as it is a channel length of the virtual network used for sending / receiving data . For FTP servers the default port is 21, but another port can be used.
Open the router configuration and look for the option of port forwarding. Enter the internal IP address of the FTP server and the port number and then save the information. When a user tries toAccess to the FTP site must be assigned to the ISP's IP address for the router. The router will then establish that the data is sent on port 21 and then forward it automatically to the FTP server. A web server is setup the same way, but the default port is in Rule 80;
Note: By default, a router dynamically assign IP addresses to computers connected to it. This means that the first computer is connected to the router to get the first available IPThe address and the next to get the second, and so on. If you assign an FTP server for management, may be easier to have a static IP address on your computer in order to ensure that the FTP server is always the same IP address.
This article describes how to connect one or more computers to an Internet connection. It 'important to remember the following:
If you have a computer connected directly to the modem, so that the computers are assigned the IP address from your ISP.
WhenUsing a router that the router's IP address assigned by your ISP. Every computer connected to the router receives a local address of the router.
Router, the IP address of the provider and a local IP address. This allows you to connect to the Internet and network connections.
When you set up a computer as FTP, Web or communicate with other servers on the Internet, it is important to use the IP address of the router to access the server. Is therefore necessarySubmit application port on your server.
For more information, please read the blog technically simple.
Computer-network 